In this article we’ll take a look at refurbishing two of the earliest Mac mini models from Apple: The PowerPC G4/1.42 GHz model and the Intel-based Core Duo 1.66 GHz. Both machines are some of the earliest “polycarbonate” mini models Apple made.

In fact, the 1.25GHz and the 1.42GHz models were both introduced on January 11th, 2005. The 1.42 GHz model was the second Mac mini ever made. The 1.42 GHz model even offered a modem port option:

The 1.66GHz model followed on Feb. 28th, 2006, and was essentially the same except for the speed bump and a few extra ports on the back. It was the sixth Mac mini model. You can view comprehensive specs on every Mac mini ever made at EveryMac.

While this teardown is mostly for the 1.66 GHz model, the first fourteen Mac minis were very similar, so most of this guide applies to all those models as well.

Getting started

First, we should caution you that these machines are very delicate inside and contain numerous tiny and fragile parts. As nearly two decades have passed, their plastics are likely to be brittle, and disassembling them always carries the risk of damage to components, so proceed with caution.

You’ll need the following tools to take one of these Mac minis apart:

A 4.5-inch (11.5cm) wall spackling tool A medium magnetized Phillips-head screwdriver A tiny magnetized Phillips-head electronics screwdriver, or jeweler’s screwdriver A small flat plastic or metal spudger Scissors Compressed air or an air compressor A bright flashlight Bright room lighting Optionally a small magnifier or jeweler’s loupe A small roll of Kapton tapeKapton tape A CR2032 replacement button-cell battery Sharp eyes and a steady hand

Step 1: Open your Mac mini

To open your Mac mini, lay it face down on a flat surface with a thin cloth underneath to prevent damage. Rotate it so the front of the machine is facing you.

Using the 4.5-inch wall spackling tool, carefully wedge the tool into the machine’s case on the right side between the outer metal cover and the white plastic rim. With one motion, press down on the tool’s handle and to the right, applying upward force.

The right edge of the case should come loose.

Next, repeat the process the same way but on the front of the case, using a single quick motion to pry it up.

Finally, work the tool into the case’s left side at the back corner and slide it forward to fit it fully into the case. This step is the hardest because with the case now tilted, there’s a lot of friction and little space on the left side.

Pry up as with the other two sides, until the bottom of the machine comes loose from the top metal cover. Don’t remove it fully yet – just pry until the two halves are separated, then remove the tool.

Now flip the machine over, and holding it with both hands, use your thumbs at the rear of the machine on the bottom half, pressing it fully free from the top cover. You’ll probably hear a slight crunching sound as the top comes off. Set it aside for now.

On the inside, as shown in the photo below, you’ll notice a DVD drive on the top, an AirPort antenna on the back right side, an optional Bluetooth antenna/case sensor on the left side, a speaker, and the button-cell battery on the front. The IR remote’s sensor is also on the front right side, with its cable attached to the front of the motherboard at the bottom of the case.

On the DVD drive, you’ll note 4 tiny Phillips screws, and two larger Phillips screwed along the left side. The four tiny screws hold the DVD drive onto the main central plastic carrier, and the two larger screws help hold the 2.5-inch internal hard drive to the underside of the carrier.

There are 4 tiny screws at each corner of the main carrier, and they’re easy to miss if you don’t look closely. Two of them are hidden down small shafts on the two right-side corners, and a third tiny one is visible on the carrier at the left corner.

The fourth, and slightly larger carrier screw is also hidden in a small shaft on the machine’s rear left corner. Make note of this screw because it will be important later.

At the rear of the machine is a small printed circuit board (PCB) attached to the rear of the DVD drive, also with two tiny screws. There’s also a small flat ribbon cable attached to a tiny connector at the center of the PCB.

Also note that the AirPort antenna’s wire fits between the left side of the PCB and the rear plastic exhaust vent.

Step 2: Loosen the AirPort antenna

Using two fingers, very carefully and slightly pinch the two small plastic clips under the AirPort antenna module and lift up on the module. It will come free from the post it sits on. There’s also a spring under it, so remove that and set it aside.

It doesn’t take much force to squeeze the two plastic clips to free the antenna, so don’t apply too much force. Remember, the plastics are brittle.

The antenna module is made by Tyco and has an Apple part number on the bottom of it should you need to replace it.

Step 3: Loosen the DVD drive screws, ribbon cable, and board

Next, using your tiny screwdriver, remove the four screws on both sides of the DVD drive and set them aside. They’re easy to lose so be careful. Don’t yet remove the two tiny screws on the PCB.

Note that the other end of the ribbon cable is attached to the motherboard at the back of the unit so it has to be freed first before you can remove the main carrier unit from the computer.

Next, using the spudger tool or a very thin hobby knife pry up the tiny plastic connector holding the ribbon cable in place. This connector has two parts: a top and bottom.

Pry one end up carefully, then pry the other end up slowly while pulling up gently and slowly on the ribbon cable. When just enough force is applied, the cable will come free.

One odd thing about this connector is that the small flat top part will come completely off if you apply enough force once the ribbon cable is free. You’d rather avoid that happening, so be very careful and go slowly.

The other odd thing about this connector is once the ribbon cable is re-inserted, the friction on the top part of the connector increases and it’s harder to move. We’ll see this in action when we reassemble the unit below.

Step 4: Remove the main carrier unit from the Mac

Using the spudger or a tiny knife, carefully unplug the IR sensor module’s two-wire connector on the front of the machine, to the right of the button-cell battery. Be very careful as the connector and wires are tiny and fragile.

In this photo, from left to right are: the speaker, case clip, battery, IR sensor connector, IR sensor:

Next, using the tiny screwdriver, remove the four tiny screws located at each corner of the carrier as described above. These screws hold the carrier unit to the bottom of the machine’s case.

Once the screws are free, and holding the unit in both hands, pull up on the carrier unit, and press down on the bottom of the machine with your thumbs.

You’ll feel a slight resistance. That’s the DVD drive’s small PCB which is inserted into the SATA connector on the motherboard underneath.

Continue pressing until you overcome the resistance and the carrier unit comes free of the bottom half. Also be careful of the AirPort antenna wire while you do this as it is connected to an AirPort module just under the PCB.

Set the bottom half of the machine aside for now.

Step 5: Remove the DVD drive

Next remove the two tiny screws from the DVD drive’s PCB board.

Now that all the screws and cable are free, you can remove the DVD drive. It tends to want to come out on the side opposite the two large drive screws on the left side of the machine, so gently press forward and to the right side (left side if facing the machine from the back) to slide the DVD drive both out of the carrier and to detach it from the PCB at the rear.

Set the DVD drive aside for now.

Step 6: Remove the hard drive

Most of the early Mac minis shipped with a 2.5-inch standard hard drive. You’ll probably want to replace the drive with a new 2.5-inch SATA SSD or a larger capacity 2.5-inch hard drive.

Flip the carrier unit over, and peel off the T-shaped foam pad on the bottom of the hard drive. Set it aside.

Next, remove the two large screws on the left side of the carrier, and the two similar large screws from the bottom of the hard drive. Once the screws are free, only the drive’s SATA connector friction holds it to the carrier.

You’ll need to press the drive forward and to the left to free it from the PCB’s connector. You may need to wiggle it slightly to free it.

It’s rather remarkable how Apple sandwiched the drive into the carrier unit.

Step 7: Remove all dust

Now, using compressed air or an air compressor, blast all the dust out of the carrier, the fan unit, the hard drive, DVD drive, and from the bottom half of the computer. The vendor and model number of the fan are printed on the fan’s bottom side so if your fan has failed, you can find a new one online to replace it.

To really clean the fan well, it can be removed by loosening the 3 tiny screws holding it in, but it’s probably not necessary. A few strong blasts of air are enough to remove most dust and dirt.

Also, note that the PCB never comes completely free of the carrier as it has several other wire connectors and is attached to the rear of the carrier with adhesive. There’s no need to remove it unless it’s damaged.

Once the hard drive is removed and all parts are cleaned, reassembly is basically the same steps in reverse.

Step 8: Install a new 2.5-inch drive

Install the new 2.5-inch SSD or hard drive into the carrier in the same way you removed the old one, taking care to be sure its SATA connector is firmly seated on the PCB’s connector.

Re-install all four drive screws, and then press the T-shaped foam strip back into place in the same position you removed it from, but on the new drive.

Step 9: Re-install DVD drive

Slide the DVD drive back into the carrier, with its rear SATA connector attaching to the SATA connector on the front of the PCB. Reinstall the two tiny PCB board screws using the screwdriver.

You can also reinstall the four side screws on the DVD drive now, or do it later. Doing it now makes the carrier unit more stable, and it’s easier than doing it once the carrier is reinstalled, but either way will work.

Here is the fully cleaned and reassembled carrier:

Step 10: Clean and check lower assembly

Before you reinstall the carrier to the bottom of the machine, inspect the motherboard, the AirPort card, its antenna cable, and other parts. In particular check the small round SMD capacitor marked “25V” at the left edge of the motherboard next to the AirPort card.

These capacitors contain electrolytic fluid and are known to leak over time. If you notice any corrosion or discoloration around the capacitor, you should probably replace it using a soldering iron, but that’s beyond the scope of this tutorial.

Also, be aware of any strange smells around the capacitor – the electrolytic fluid inside these components is known to have a somewhat fishy smell, so if you notice any odd odors, that’s the first thing to check.

You’ll also want to check the tiny gold connector at the end of the AirPort antenna cable where it attaches to the AirPort card. These connectors are notorious for coming loose easily and when you go to reinstall the carrier unit to the bottom of the machine, it’s easy to pull the cable off.

It’s odd Apple didn’t secure the connector with a small strip of Kapton tape. If you have any handy, go ahead and apply a small piece over the connector now to secure it to the AirPort card.

Note the carrier’s PCB board socket just behind the AirPort card. When you reassemble the machine, you’ll need to make sure the PCB connector’s edge fits snugly into this socket.

Step 11: Optional – Replace RAM

If you like, you can upgrade the machine’s RAM to a maximum of 2GB. The specs for the RAM are listed on EveryMac, and are shown below:

Both memory DIMMS must be the same type and speed, but size can vary within limits – for example, a 1GB and a 512MB together will work fine – as long as both combined don’t exceed the maximum RAM limit (2GB).

To remove the old DIMMs, press gently on the two small metal clips on each side while pulling up the DIMM and sliding it forward, out of its socket. Be careful as the clips are tiny and can easily break off if too much pressure is applied.

To install new DIMMs, do the reverse: slide each new DIMM into its socket until it clicks, then press down slightly to lock the clips in place.

Step 12: Optional – Replace button-cell battery

Next, using the spudger or small plastic knife, remove the CR2032 button-cell battery from its socket on the front of the lower half of the machine. There are two metal contacts holding it in place, so you may have to wiggle it a bit to remove it.

If you have a voltmeter, test the battery to make sure it can emit 3V DC. If not, replace it with the new one.

If you don’t have a voltmeter, go ahead and replace the battery anyway. Be sure the “+” side faces the front of the machine.

Also note the tiny copper clip just to the left of the battery. This piece actually connects to the bottom of the DVD drive’s metal case, and the inside front of the machine’s top case, creating a connection.

If this connection is broken, the machine won’t work.

The copper clip tends to come off over time as it’s only held on by thin adhesive on the top of the carrier, and the adhesive usually dries out over time. If this is true on your machine, or if the clip falls off, just reattach it with a drop of Loctite or another fast-drying adhesive.

There’s a small peg on the top of the carrier, and a small hole on the back of the copper clip which it fits onto – so it should be easy to line up. Notice it doesn’t make any connection to the carrier itself – only between the DVD drive and top case.

Finally, reconnect the IR receiver’s small two-wire plug onto the motherboard just to the right of the battery.

Step 13: Reinstall the carrier

With the bottom half of the unit facing away from you, lower the carrier down onto the bottom half of the machine, making sure the PCB board’s connectors are lined up, and that the four corner screw holes are lined up.

Also, make sure the AirPort antenna’s cable is positioned between the rear exhaust port and the small PCB attached to the rear of the machine. The cable has to come up through this opening, then to the left in order to reinstall the antenna on the carrier:

Press down gently until the carrier’s PCB locks in place. Reinsert the four corner screws, making sure the largest one is reinstalled in the same position it was removed from.

This is important because the screw creates a ground connection to the top of the motherboard once secured. Without this connection, the machine won’t work.

Don’t over-tighten the screws as it’s easy to strip the threads on both the screws and the bottom case. Apply just enough force to make them snug.

Step 14: Reconnect the PCB ribbon cable

This is perhaps the most difficult and fiddly step of reassembly. You’ll need to reconnect the carrier’s ribbon cable to the rear of the PCB using the small clip on the PCB.

The easiest and best way to do this is to reposition the top half of the connector, snap it on fully, then using the spudger or a hobby knife, pry both corners back up just a bit, but not enough to remove the clip. Do this before you reinsert the cable.

While the clip is in this position, reinstall the ribbon cable into the PCB connector by pressing it gently down into place. Once it snaps into the connector, the top half of the clip will be captive and won’t come off. You can then press each corner of the clip down using your tiny screwdriver.

Once both sides of the clip are secured, the entire connection will be solid and won’t come loose.

It may take a few tries to get the clip in place but with patience, it’s fairly easy. Go slow and don’t apply too much force. If in doubt, remove the ribbon cable and start over.

The final, correct connection is shown below, under the right arrow:

Also note the position of the AirPort antenna cable, just to the left.

Step 15: Reinstall AirPort antenna

Now that the carrier and ribbon cable are secure, reinstall the AirPort antenna onto its post by first reinstalling the spring onto the post, then snapping the antenna board down onto the two small plastic clips on both sides of the post. The antenna will lock into place.

The spring acts as yet another security/electrical feature designed to prevent the machine from working unless the case is assembled: it presses down slightly and makes contact, acting like a switch once the case is closed.

Without the antenna module being pressed down when the case closes, it won’t work.

Here’s the fully reassembled Mac, except for the top case:

Step 16: Reinstall top case

This final step is also difficult to get perfect but can be done with patience.

The main difficulty in reinstalling the top half of the case onto the bottom half is the fact there are both plastic clips all the way around the bottom half on three sides, and there are also small metal clips around the rear panel on the bottom half.

The metal clips also act like a switch and must make contact with the metal inside of the top half of the case.

The initial alignment and closure of the case are fairly easy, but closing it completely requires a fair amount of force, and if everything isn’t lined up perfectly, either the plastic clips can break off, or else the metal clips can slip outside the top half of the case and prevent it from closing completely.

If the latter happens, the case will appear to close, but there will be a small gap around the rear panel where the top half of the case seats against it.

In order to avoid this, flip the top half of the case face down on a surface, with the front facing away from you, then flip the bottom half over and slowly lower it into the top half.

Check the clips on all sides, and the rear, and press down very slowly and gently, but don’t close the case completely.

After the two halves slide together, and the top half has cleared all the plastic clips on all sides, stop, and flip the machine on its front, with the rear panel facing up. Using a flashlight, inspect the alignment of the metal clips all the way around the rear panel.

If any are outside the top half of the case, use your tiny screwdriver to press them down and inside the top half.

You may have to wiggle them a bit to get the alignment perfect. Note that they are slightly curved, and thus act like small springs against the top half of the case on the inside.

You want the clips on the inside, not the outside all the way around the rear panel. What you don’t want is this:

If this happens, you’ll need to walk the top half of the case back off just a bit, press the metal clips in place, then reapply pressure to the bottom.

Once you’re certain all the clips on all sides are in perfect position, and that nothing is protruding, lay the machine top-down on a surface once again, and give the bottom of the case one final even downward push with force. This will seal the case – as if it had never been opened.

There should be no gaps on any sides, anywhere – not even tiny ones. If there are, you’ll need to use the spackling tool to open the case again and start over. Take your time and be careful. Forcing the case closed won’t work unless everything is perfectly aligned.

Step 17: Reinstall Mac OS X

Now that the physical hardware modernization is done, it’s time to install software.

Reconnect the machine to a monitor via DVI or DVI->HDMI using an adapter, and plug in its power brick.

With an appropriate Mac OS X install CD or USB thumb drive ready, power on the machine.

You should hear the customary bong sound and get a grey screen with a flashing folder. This means the machine can’t find an OS on any bootable drive.

Either insert a Mac OS X installer DVD or a USB thumb drive with an installer on it, and the Mac should detect it and boot into the install media.

Once booted, you’ll need to exit the installer to Disk Utility, format the new internal 2.5-inch drive you installed as Mac OS Extended, then quit Disk Utility and head back into the installer.

Once back in the installer, select the internal 2.5-inch drive as the install target and install the OS. It may take some time if you are installing from DVD as the old DVD drives tend to be a bit slower.

The 1.66 GHz mini model can run Mac OS X 10.6 Snow Leopard, and the 1.43 GHz model can run 10.4 Tiger.

Once the installer finishes, click Restart, and after the bong sound, hold down the Mac’s mouse button. This will force-eject the DVD before the machine boots. Or if using a USB installer, be sure to unplug it from the Mac before restarting.

The machine will boot from the internal 2.5-inch drive you installed onto. Once booted to the Finder, open System Preferences, and click the “Startup Disk” icon. Set the internal 2.5-inch drive as the Startup Disk for future booting.

Once connected to a network, you may want to also try to run Software Update but it’s not clear how long Apple supports ancient versions of Mac OS X for on their update servers.

There are also downloadable .pkg installers for the updates, but you’ll need to search Apple’s support site or online to find them.

The last released version of Mac OS X 10.6 was 10.6.8 so if you’re using a model that supports 10.6, you’ll want to update to that version.

And just like that, your newly refurbished Mac mini lives again:

Bonus: Install Mac OS Classic (Mac OS 9)

If you’re using a Mac mini which is able to run 10.4 Tiger, you can also install the “Classic” environment which is a built-in emulator which runs Apple’s OS that came before Mac OS X: Mac OS 9.

To start Classic in 10.4 Tiger, open System Preferences and click “Classic”. It will boot into the OS 9 emulator and you can run OS 9 apps from there.

In most cases, the Mac OS 9 System Folder gets installed onto the root of the Mac OS X boot drive alongside Mac OS X.

Third-party drives and accessories

Note that all mini models before the 1.66 GHz 2006 model used ATA/100 hard drives, including the optical drive (ATAPI actually for optical), and the 1.66 GHz and later models switched to SATA hard drives but kept the same ATAPI DVD drive.

If the DVD drive in your 2006-2007 mini isn’t working, one company – Other World Computing – still sells new replacement ATAPI DVD drives ($48). All compatible mini models have a hardware identifier of “Macmini1,1”.

Even if your optical drive hasn’t yet failed, at that price it’s probably worth replacing it anyway, since it’s likely to fail in the future, and the brand-new hardware will almost certainly yield better performance than a nearly twenty-year-old drive.

And it’s probably not a good idea to open these old machines too many times and risk damage.

OWC also sells compatible memory upgrades for older minis. The 2GB upgrade comprising two DIMMs is a mere $12 currently.

With new RAM, a new SSD, a new optical drive, and a good cleaning, your retro Mac mini should give you years more enjoyment into the future.